High Purity 3D Printing Powder 15-5 Stainless Steel Powder

About the 3D Printing 15-5 Stainless Steel Powder: Stainless 15-5 metal powder can be used for 3D printing of thin-walled parts and devices, cold and hot spraying, laser cladding and biomedical applications. Stainless Steel PH 15-5 is a martensitic, precipitated stainless steel that has excellent corrosion resistance at temperatures as high as 600degF (316degC), and also good mechanical properties.
This stainless steel is pre-alloyed and fine powder. This steel has excellent corrosion resistance, and good mechanical properties. This type is used widely in medical, aerospace, engineering and other applications where corrosion resistance and high hardness are needed.
In metal injection molding, precipitation hardening is the most commonly used alloy. Cu tends to evaporate when sintering, which is one of its potential disadvantages. It may be necessary to clean the oven regularly in order to prevent cross-contamination. The current study of 15-5pH has been initiated in part with this aspect in mind.
It is a martensitic, precipitate-hardened stainless alloy containing 15 chromium. It has a high degree of strength, hardness and corrosion resistance. Heat treatment at low temperatures can increase the strength. It is stronger and more malleable than 17-4 pH. It welds well. It can be used in this level for any thermal condition. If you are interested in purchasing 3D Printing Powder Stainless Steel Powder, 15-5, in bulk quantities, please send us an inquiry.

Stainless Steel powder category:
Alloy grades & Characteristics
Alloy number of Stainless Steel Stainless Steel powder
Stainless steel:304,316L,410L,15-5PH,17-4PH,2Cr13;
High-strength steel:A100,300M,30CrMnSiA,40CrMnSiMoVA;
Work die steel:18Ni300,H13,M2,M35,M42,T15,2030,S390
Iron Nickel Alloy Powder: Invar 36
The particle size of Stainless Steel powder is:
0-20mm, 15-45mm, 15-53mm, 53-105mm, 53-150mm, 105-250mm

Morphology and morphology of Stainless Steel Powder
Spherical or near spherical

The appearance and properties of Stainless Steel powder
Grey

Package of Stainless steel powder
Aluminum bag, Vacuum packing

Stainless Steel powder application:
3D printing powder

Other uses for Stainless Steel powder
powder metallurgy(PM), injection molding(MIM), spray painting(SP) etc.

How does 3D printing powder 15-5 Stainless-Steel Powder get produced?
The 15-5PH stainless is an upgrade of the 17-4PH that was developed in the 1960s. This finer structure was achieved by the remelting procedure. This delicate construction increases the material's strength. The material has excellent corrosion resistance and is suitable for a wide range of industries. It can be processed either in the solution annealing stage or the final heat-treatment state. Heat treatment at different temperatures improves the strength and ductility.
Any conditions are acceptable for processing 15-5PH. The alloy must first be slightly formed under the condition of average. Then, it is welded by using techniques like resistance or protective fusion. The material was heated at 1038degC (1900degF), then cooled with air for 1/2 hour. It is then followed by annealing the alloy at 1038degC for 1 hour and cold working.

Applications Stainless Steel Powder 15-5 for 3D Printing
15-5PH stainless may be used for heating or resolving treatment conditions in order to obtain various properties. The stainless steel can be treated in many different ways, but the H1150m treatment conditions provide the best life expectancy.
Applications: aerospace parts, aircraft manufacturing, component manufacturing and other equipment.
Here are a few other uses for stainless steel 15-5.
The marine gas compressor section
Hollow shaft,
Papermill equipment
Engine parts
Aircraft parts
gear
Fittings & fasteners
Nuclear reactor assembly
Aerospace structural components
The valve
The gear and shaft
Oil and Gas Components
Nuclear reactor assembly

Storage Condition for 15-5 Stainless Steel powder:
As dampness will affect the performance of 15-5 powder and its use, it is important to store 15-5 stainless-steel powder in a dry and cool room. Ti2AlC Powder should not be exposed to stress.

Shipping & Packing of 15-5 Stainless Steel Powder
The amount of powder 15-5 stainless is used to determine the type of packaging.
15-5 stainless powder packaging: Vacuum packed, 100g/bag, 500g/bag or 1kg/bag. 25kg/barrel or according to customer's request.
15-5 Stainless Steel Powder Shipping: Can be shipped by sea, air or express as quickly as possible after payment receipt.